Insulation cost by size
The biggest driver is size: 500 sq ft costs $680-$1,130 in Arlington, while 2,500 sq ft costs $2,900-$4,820, about 327% more. Ask every contractor to quote the same measured size.
| Size | Cost |
|---|---|
| 500 sq ft | $680-$1,130 |
| 1,000 sq ftMost common | $1,230-$2,050 |
| 1,500 sq ft | $1,790-$2,970 |
| 2,000 sq ft | $2,340-$3,900 |
| 2,500 sq ft | $2,900-$4,820 |
Installed: Blown-in fiberglass, attic (R-38)
Insulation cost by material or type
The gap between options is wide: spray foam, closed-cell (2 in.) costs about 2.7 times as much as blown-in fiberglass, attic (R-38) in Arlington, and radiant barrier (attic) trims about 26%.
| Type | Typical job | Installed |
|---|---|---|
| Radiant barrier (attic) | $880-$1,540 | $0.75-$1.34 installed |
| Blown-in fiberglass, attic (R-38)Most common | $1,230-$2,050 | $1.11-$1.85 installed |
| Blown-in cellulose, attic (R-38)Most common | $1,230-$2,050 | $1.11-$1.85 installed |
| Fiberglass batts, walls (R-13) | $1,420-$1,820 | $1.29-$1.62 installed |
| Rigid foam board (R-5 per inch, 2 in.) | $1,700-$4,130 | $1.57-$3.93 installed |
| Fiberglass batts, attic floor (R-30) | $2,050-$2,400 | $1.92-$2.19 installed |
| Spray foam, open-cell (3.5 in.) | $2,160-$3,210 | $2.03-$3.00 installed |
| Dense-pack cellulose, existing walls | $2,470-$3,410 | $2.34-$3.20 installed |
| Mineral wool batts (R-15) | $2,570-$3,580 | $2.44-$3.37 installed |
| Spray foam, closed-cell (2 in.) | $3,720-$5,280 | $3.60-$5.07 installed |
Materials include waste and contractor markup. Typical job: 1,000 sq ft
What will your Arlington insulation project cost?
We have already loaded Arlington prices for this insulation estimate. Enter your project details and ZIP code for a free planning estimate.
Add-ons and extra work
Not every insulation job needs these, but ask about each one before you sign. In Arlington, the biggest line is "Air sealing (attic)" at $669-$1,010 for the job.
- Remove old insulation$1.30-$1.76 / sq ft
- Air sealing (attic)$669-$1,010 / job
Show material-only prices
| Add-on | Materials |
|---|---|
| Remove old insulation | $0.06-$0.14 / sq ft |
| Air sealing (attic) | $115-$288 / job |
Installed price per unit
What makes Arlington different for this job
Arlington homes and the local housing stock
How old Arlington homes are, and what that means for insulation
Arlington insulation jobs happen in homes older than those in the other Texas cities NumeralQ covers: half were built in 1986 or earlier, against 1994 there. By room count, the median Arlington home is about average: 5.3 rooms against 5.5 for the other Texas cities NumeralQ covers, which sets the scope of most insulation jobs.
A typical insulation job at the midpoint price equals roughly 0.5% of what the median Arlington home is worth ($304,700), 64th of the 147 markets NumeralQ covers.
Because the median home dates to 1986, an Arlington attic usually has code-era insulation in it. Ask the installer to measure it, since topping up costs less than starting from bare joists.
Local planning note for Arlington
Arlington next to Fort Worth and Dallas
Arlington and its two nearest neighbors on this site, Fort Worth and Dallas, land within a few tenths of a point of each other when the typical insulation job is set against the median home value.
BLS counts Arlington, Fort Worth and Dallas as one labor market for insulation workers, so a cheaper insulation job quote from the next city over reflects the contractor, not local pay.
| City | Typical job (midpoint) | Share of median home value | Pay for insulation workers vs U.S. |
|---|---|---|---|
| Arlington | $1,640 | 0.5% | +2% |
| Fort Worth | $1,640 | 0.5% | +2% |
| Dallas | $1,640 | 0.5% | +2% |
Typical job: midpoint of NumeralQ's typical-job range for each city. Pay: BLS May 2025 median for the trade vs the U.S. median.
Arlington Insulation Pricing — 2026 Local Market
Insulation cost in Arlington, TX: $1,230-$2,050 (typical job: 1,000 sq ft).
Arlington's climate and insulation
ENERGY STAR's attic recommendation for climate zone 2A, which covers Tarrant County, is R49 to R60.
A typical year in Arlington brings 2,126 heating degree days and 2,824 cooling degree days (NOAA, 1991–2020), a standard way to measure how much heating and cooling a climate calls for.
For comparison, the median station in Texas records 2,230 heating and 2,585 cooling degree days, and the U.S. median is 5,483 and 848.
Texas builds new homes to the 2015 IRC energy chapter. For an existing attic, ask the installer to write the installed depth and R-value on the invoice.
| Climate zone (county) | 2A |
|---|---|
| ENERGY STAR attic level | R49 to R60 |
| Heating / cooling degree days | 2,126 / 2,824 |
| Federal 25C insulation credit | Ended for work placed in service after 2025 |
| Contractor license (Texas) | No state general or remodeling license; some cities register contractors |
| Where to check a license | City or county building department |
Local data checked October 2026 · Sources at the bottom of the page
Local planning note for Arlington
Oncor efficiency incentives in Arlington
Oncor delivers power to most of Arlington, and its Home Energy Efficiency incentive goes to an approved contractor, who passes it on to you. You can't claim it yourself. The program usually runs February through November until funds run out, and our source is a 2022 Oncor article, so confirm this year's terms. Added attic insulation is a covered item, so book early in the year before funding runs low.
How Arlington compares with nearby cities
Labor rates
On an insulation job in Arlington, insulation workers earn a median $24.00 an hour, 2% above the U.S. median. After insurance, payroll taxes and overhead, contractors bill about $48-$62 per worker-hour.
Insulation Workers, Floor, Ceiling, and Wall
Median pay: BLS May 2025. Billed rate: what a contractor charges per worker-hour, estimated at 2.0 to 2.6 times pay (insurance, payroll taxes, overhead, profit).
Before you sign in Arlington
Get every quote to include
- assembly, insulation material, coverage area, and target R-value
- air sealing, preparation, and removal of existing material
- moisture or vapor-control details and ventilation scope
- access constraints, cleanup, and any excluded repairs
Contractors per home in Arlington
Contractor competition in Arlington
For insulating an attic or walls in Arlington, the local pool is 97 drywall and insulation contractors in Tarrant County (Census, 2023): 1.1 per 10,000 homes, 15% below the U.S. rate of 1.4. The Census counts drywall and insulation firms together, so not every one of them does insulation.
A middle-of-the-pack field means Arlington homeowners should be able to get two or three insulation job bids without long waits, outside the busiest season. The same county count applies to Fort Worth.
Frequently Asked Questions
How much does Insulation cost in Arlington, TX?
Insulation cost in Arlington, TX: $1,230-$2,050 (typical job: 1,000 sq ft). The table above breaks it out by option.
How does pay for construction laborers in the Dallas-Fort Worth-Arlington area compare with the national median?
Median pay for construction laborers in the Dallas-Fort Worth-Arlington, TX metro area is 2% above the national median, according to BLS data for May 2025. Pay is one input to a quote, not the price itself.
How old are homes in Arlington?
About 33% were built before 1980, according to the Census Bureau, against 33% across Texas and 50% nationally.
How do most Arlington homes heat?
About 26% heat mainly with piped gas and 71% with electricity, according to the Census Bureau's 2020–2024 survey.
Ready for your own number?
We have already loaded Arlington prices for this insulation estimate. Enter your project details and ZIP code for a free planning estimate.
Sources and methodology
- NumeralQ estimator (pricing as of 2026-10-26)
- Fixr cost guide, retrieved 2026-10-26
- Home Depot online prices, store 121, retrieved 2026-10-26
- U.S. Bureau of Labor Statistics, Occupational Employment and Wage Statistics, May 2025 (https://www.bls.gov/oes/)
- City permit fee schedules, retrieved October 2026 (see the permit line for this page's source)
- NumeralQ pricing model v2: materials plus local labor, methodology at /methodology
- U.S. Census Bureau, American Community Survey 2020–2024 5-year estimates, place-level tables B25018 (median rooms), B25035 (median year built), B25077 (median home value), B25024 (units in structure), B25003 (owner and renter occupancy) and B25041 (bedrooms) (https://data.census.gov/)
- NumeralQ pricing model v2: typical-job midpoints for all 147 markets, compared with the Census median home value (methodology at /methodology)
- Ready to get energy efficient? We show you how (Oncor), checked October 11, 2026 (https://www.oncor.com/content/oncorwww/wire/en/home/energy-efficiency/ready-to-get-energy-efficient--we-show-you-how.html)
- U.S. Bureau of Labor Statistics, Occupational Employment and Wage Statistics, May 2025, metro-area median pay by trade compared with the U.S. median (https://www.bls.gov/oes/tables.htm)
- U.S. Census Bureau, County Business Patterns 2023, establishments by county for NAICS 238160, 238170, 238220, 238310, 238320, 238330, 236118 and 561730, per 10,000 housing units from ACS 2020–2024 5-year table B25001 (https://www.census.gov/programs-surveys/cbp.html)
- DOE climate zone guide source
- ENERGY STAR source
- NOAA climate normals source
- DOE building energy codes source
- IRS source
This estimate is NumeralQ's national baseline with a Arlington adjustment of 0.95×. How we estimate